Automatic Bollards vs Fixed Bollards: What Security Rating Do You Need?
Essential Security Supplies
Hero illustration: a yellow FERN360 surface-mounted fixed safety bollard on a city footpath. The pictured fixed bollard is not presented as independently crash-rated; the street scene is illustrative.
The security rating you need depends on the credible vehicle threat, impact speed and acceptable penetration, not simply whether a bollard is fixed or automatic. Both forms can offer impact-rated protection where the complete system has suitable independent test evidence. This guide explains how New Zealand installers, security consultants and property teams can specify a vehicle security barrier without mistaking marketing load claims for certification.
What security rating do you need?
There is no single bollard impact rating suitable for every commercial facility. The necessary protection follows the credible vehicle threat, approach geometry, vulnerable assets and tolerated penetration distance. A low-speed accidental vehicle strike at a retail frontage is different from a deliberate high-energy approach to a critical site. Before selecting equipment, document the plausible vehicle type and mass, available acceleration distance, likely impact direction, maximum tolerable penetration, and whether authorised vehicles must cross the protective line. A formal hostile vehicle mitigation assessment may be warranted for higher-risk projects. Choose a test performance to match that assessment, not a headline strength claim.
Understanding vehicle impact standards
ISO 22343-1:2023 addresses full-scale vehicle impact testing and performance ratings for vehicle security barriers. ISO 22343-2:2023 complements it with application and selection guidance. Earlier PAS 68 and IWA 14-1 testing may remain useful evidence for existing products, but older classifications should not be represented automatically as the same as ISO 22343. ASTM F2656 is another vehicle impact testing framework, with vehicle-class, speed and penetration classifications. PAS 170 is directed at certain lower-speed bollard impacts and should not be mistaken for the same high-energy hostile-vehicle protection. Ask for the original test documentation and confirm that its barrier configuration and penetration result are relevant to the project.
K12 and M50 explained
In ASTM F2656 terminology, an M50-P1 classification indicates an M-class test vehicle at the M50 nominal test speed with penetration in the P1 band. The letter-and-number combination describes more than the impact speed: the penetration designation matters when matching a barrier to the available setback. Classification systems and measurement conventions differ, so verify the precise standard edition and original full test report before comparing results across ISO, ASTM or historical schemes.
K12 is an older US Department of State barrier classification associated with a nominal 15,000 lb vehicle at 50 mph, around 6.8 tonnes and 80 km/h. The newer ASTM F2656 system includes medium-duty vehicle speed designations such as M30, M40 and M50. Calling an untested product K12 does not make it independently certified, and a historical K12 claim is not a substitute for a complete ASTM or ISO report. Even when vehicle mass and nominal speed appear similar, examine the original test, penetration measurement, installed array and foundation. In particular, a product may stop or damage a test vehicle yet allow movement beyond the protective line that is unacceptable for a nearby building entrance.

Fixed vs automatic bollards
Fixed bollards remain in position and are generally suitable for permanent protection along pedestrian frontages, building edges and restricted boundaries. Automatic bollards rise and retract to provide controlled access at driveways or service entrances. Both types can potentially be crash-rated where the specific complete arrangement has been independently tested. Neither type is inherently assigned a rating by its operation alone. Fixed bollards do not allow routine vehicle passage through the line. Automatic bollards depend on controls, power, detection, operating procedures, drainage and maintenance, and they cannot provide raised-bollard protection while retracted. For a detailed overview of permanent installations, see the FERN360 fixed bollards range guide. For an application-based comparison, see our fixed and automatic bollard selection guide.

What the penetration result tells you
Penetration is central to protecting people or critical assets located directly behind a barrier. Two independently tested barriers may be exposed to nominally similar vehicles and impact speeds yet permit different distances of vehicle travel beyond the defined barrier reference point. The right choice depends on available safety distance and the particular standard's measurement method. Never compare two bare penetration numbers without considering their test methods, points of measurement and vehicle behaviour. At restricted pedestrian entrances, a small site setback can make a substantial difference to whether the tested performance is appropriate.
Why tonnage is not a rating
Some product descriptions refer to impact resistance using tonnes or a claimed load capacity. Static load capacity is not the same as a demonstrated vehicle impact classification. Vehicle mass and speed influence kinetic energy, but the collision response also depends on vehicle construction, strike angle, barrier structure, foundation and ground. As a simple illustrative calculation, doubling speed from 40 to 80 km/h for an otherwise identical moving vehicle increases kinetic energy fourfold. This arithmetic is not an estimate of a particular bollard's penetration or survivability. Do not translate catalogue wording such as '80 tonne resistance' into ISO, ASTM or historical K12 certification without matching primary evidence.
Step 1: document the threat
Map the vehicle approach and decide what could reasonably reach the site. Consider passenger cars, delivery vehicles and larger commercial vehicles separately; evaluate the actual access routes and constraints rather than assuming every vehicle can approach at highway speed. Describe the people, equipment or facilities needing protection and the consequence of intrusion. Record whether the protection is primarily for accidental strikes or also includes deliberate vehicle attacks. This distinction guides the choice of suitable test evidence.
Step 2: decide acceptable penetration
Measure the distance between the planned protective line and the people or assets to be protected. Include the possibility of vehicle overhang and other movements described in test documentation where relevant. Select a tested penetration result compatible with the site rather than just a large nominal impact speed. A barrier may be structurally effective but still unsuitable for a closely positioned entrance or occupied pedestrian area.
Step 3: require full certification evidence
Request the exact tested model, complete impact classification, test-house evidence, installation drawing, ground conditions, barrier spacing and measured penetration. Check whether a single unit or complete array was tested and whether the supplier proposes that arrangement for your site. If the manufacturer offers several variants with different foundations, do not transfer one variant's certification to another. A certificate does not automatically validate altered footings, anchorages or spacing.

Step 4: design foundations and services
Review existing slabs, underground utilities, drainage, ground strength and structural interfaces before finalising the bollard choice. Where deep excavation is restricted, investigate a suitably tested shallow-foundation configuration instead of improvising a smaller footing. Automatic systems also need power, hydraulic or electromechanical equipment as relevant, safe cable routes and maintenance access. Any change from the tested configuration should be assessed by competent designers and the manufacturer. For site-level drainage, power and civil works, read our automatic bollard installation guide.
Step 5: design safe access operation
For automatic bollards, plan authorisation, vehicle detection, visual and audible warnings as appropriate, operating speed, fault conditions, emergency access and the site's safe movement procedures. Establish the intended response to loss of power or communications. The protected boundary's effectiveness changes when an automatic unit is lowered, so access privileges and monitoring form part of the operational security strategy. A crash-test certificate is not a complete safety approval for moving equipment. Under New Zealand's Health and Safety at Work Act 2015, relevant businesses designing, installing, commissioning or controlling powered barriers at workplaces must manage applicable health and safety risks so far as is reasonably practicable. WorkSafe's automated gates safety alert recommends risk-appropriate safeguards for moving gates, including warning devices, safety sensing, force limitation and reversal, clearly labelled emergency stop and manual release; assess equivalent hazards and appropriate safeguards for the particular automatic bollard system rather than assuming gate measures apply identically.
Step 6: inspect and maintain
Record routine checks appropriate to the manufacturer, environment and site risk. Inspect for corrosion, movement, settlement, drainage problems, impact damage and changes to surrounding pavement. Automatic systems need additional checks of sensors, controls, mechanisms and emergency operating procedures. After a significant strike or suspected structural damage, seek competent assessment rather than assuming the original impact rating still applies. Keep the commissioning, test and maintenance record with the facility documentation.
New Zealand specification considerations
Commercial New Zealand sites may have constrained pedestrian frontages, sloping vehicle approaches, existing underground services and shared pedestrian/vehicle entries. Such conditions can affect the correct location and foundation design. If work extends into a public road corridor or footpath, permission from the relevant road-controlling authority may be required. Emergency egress, access arrangements and worksite safety must be assessed against applicable requirements for the project. Do not assume an overseas test certificate removes the need for NZ site-specific structural and operational design.
Common specification mistakes
Avoid choosing only by post diameter, finish or appearance. Do not treat a K12 marketing label as proof of independent testing or ignore the penetration result. Do not substitute an untested foundation, assume an automatic unit protects the entrance while lowered, or treat a single impact test as proof against repeated, slow-speed or other attack methods outside its scope. Each of these mistakes can leave a gap between the specified objective and the demonstrated performance.

Choosing the right solution
Fixed bollards provide a permanent protective line; automatic bollards allow controlled vehicle passage. The decisive issue is the independently documented performance of the actual installed arrangement against the defined threat. For trade projects, prepare a site plan, vehicle access pattern, protection objective, anticipated vehicle classes and preliminary civil drawings before selecting equipment. View ESSL automatic bollard options, compare the fixed bollard range, and contact our team for model-specific documentation and specification support before making any impact-certification claim.
Frequently asked questions
Are automatic bollards as secure as fixed bollards?
Either can achieve a suitable tested impact rating. Compare the actual classification, penetration result, foundation and operating state, not the fixed or automatic label.
What does K12 mean on a bollard?
K12 is a historical US Department of State vehicle-impact classification involving a nominal 15,000 lb test vehicle at 50 mph. Require original evidence for any claimed rating.
Is ISO 22343 better than PAS 68?
ISO 22343-1 is the current international impact-testing reference. Legitimate historical PAS 68 tests can remain relevant, but the complete tested performance and installation matter.
Do all commercial bollards need a crash rating?
No. Some manage ordinary vehicle movement or limited accidental strikes. When relied on for a defined vehicle-security threat, independently tested performance should be specified.
Can the foundation affect a bollard rating?
Yes. Foundation and ground conditions influence performance. Changes from the tested arrangement may affect the applicability of its rating.
Technical references
Relevant primary references: ISO 22343-1:2023 and ISO 22343-2:2023. Confirm current applicable standards and manufacturer test reports before specifying any security rating.